How to Use Ceramic Spray Coating | CeramiQ + OPAL 1200 Guide

How to Use CeramiQ Nano Ceramic Spray Coating With the OPAL 1200 Buffing Towel

If you want your car to look glossier, feel smoother, and bead water after washing, CeramiQ is the finishing step to use.

CeramiQ is CabinCraft’s quick nano ceramic coat spray. It is designed to add gloss, slickness, and water-repellent protection to clean exterior surfaces. The OPAL 1200 is the microfiber buffing towel used to spread, level, and finish the product properly.

This guide is written for beginners. No complicated detailing language. No overthinking. Just a clear step-by-step process for using CeramiQ safely and getting a clean, glossy finish.

CabinCraft - details drive the experience.

Quick answer: Wash and dry the car first. Spray a light mist of CeramiQ onto one panel or onto the OPAL 1200 towel. Spread evenly, then buff immediately with a clean side of the towel until the surface is clear, glossy, and streak-free.

What You Need

·       CeramiQ Quick Nano Ceramic Coat

·       OPAL 1200 Microfiber Detailing Towel

·       A second clean microfiber towel, if available

·       A clean, freshly washed and dried vehicle

CeramiQ adds gloss, slickness, and water-repellent protection.

OPAL 1200 helps spread, level, and buff the product for a clear finish.

Where You Can Use CeramiQ

·       Paintwork

·       Headlights

·       Taillights

·       Exterior trims

·       Rims

·       Tyres, if desired

For beginners, start with painted panels first. Once you are confident, you can use it on other suitable exterior surfaces.

Before You Start

Only apply CeramiQ when the car is:

·       Clean

·       Cool to the touch

·       Out of direct sunlight

·       Free from heavy dirt, dust, or road grime

Do not apply CeramiQ to a dirty car. Always wash first. For best results, use it after washing and drying the vehicle.

Simple Step-by-Step Process

Step

Action

What to Do

1

Wash and dry the car

CeramiQ should be applied to a clean surface. Wash the vehicle first, then dry it properly before starting.

2

Fold the OPAL 1200

Fold the towel into quarters so you have multiple clean sides to spread and buff the product.

3

Work one panel at a time

Do not spray the whole car at once. Start with one door, half a bonnet, one guard, or one small section.

4

Spray CeramiQ lightly

Use a light mist on the panel or directly onto the OPAL 1200. Too much product can cause streaks.

5

Spread evenly

Use gentle straight lines or a cross-hatch motion to spread the product across the panel.

6

Buff immediately

Flip to a clean side of the towel and buff until the surface is clear, glossy, and streak-free.

7

Check the finish

Look from different angles for streaks, haze, or high spots. Rebuff gently if needed.

8

Let it set

Keep the treated surface away from water for at least 2-4 hours where possible. Avoid detergent washing for 24 hours.

Step 1: Wash and Dry the Car First

CeramiQ works best on a clean surface. Wash the car properly, rinse off all shampoo, and dry the vehicle before applying the product. Do not apply CeramiQ over dust, dirt, or water spots.

Step 2: Fold the OPAL 1200 Towel

Fold the OPAL 1200 into quarters. This gives you multiple clean sides. Use one side to spread the product, then flip to a fresh side to buff the surface clear.

Step 3: Work One Panel at a Time

Work in small areas so the product stays easy to control. Start with one door, one guard, one mirror, or half a bonnet. Do not spray the whole car at once.

Step 4: Spray CeramiQ Lightly

Use a light mist of CeramiQ on the panel or directly onto the OPAL 1200. A small amount is enough. Using too much product can make the panel streaky and harder to buff.

Step 5: Spread the Product Evenly

Use the OPAL 1200 to spread CeramiQ across the panel using gentle straight lines. You can also use a cross-hatch pattern for more even coverage. Do not press hard.

Step 6: Buff Immediately

After spreading, buff the same area straight away with a clean side of the OPAL 1200. Buff until the surface looks clear, glossy, smooth, and free from streaks or haze.

Step 7: Check for Streaks or High Spots

Look at the panel from different angles. If you see smears, cloudy patches, or high spots, rebuff gently with a clean side of the towel. A second clean microfiber towel can help with the final wipe.

Step 8: Let the Protection Set

After application, keep the treated surface away from water for at least 2- 4 hours where possible. Avoid washing the car with detergents for 24 hours after application.

Beginner Mistakes to Avoid

Using too much product: More product does not mean better protection. A light mist is enough.

Applying in direct sunlight: Hot panels can make the product flash too quickly and leave streaks.

Spraying the whole car at once: Work one panel at a time so the product stays easy to control.

Letting it dry before buffing: CeramiQ should be spread and buffed immediately.

Using a dirty towel: Always use a clean OPAL 1200 towel to avoid dragging dirt across the paint.

Pressing too hard: Soft, controlled movements are all you need.

Final Thoughts

CeramiQ is the finishing step that brings the wash together. It helps add gloss, slickness, and water-beading protection after the car has been cleaned.

The OPAL 1200 gives you control during application. It helps spread, level, and buff the product so the surface is left clear and refined.

Use a clean surface. Apply a light mist. Work one panel at a time. Buff immediately. Check your finish.

CeramiQ gives the protection. OPAL 1200 gives the finish.

CabinCraft - details drive the experience.

Back to blog